Full Visual Inspection
We walk the entire property, including attic, crawl space, HVAC closet, bathrooms, and under sinks. We look for visible growth, water stains, peeling paint, and warped materials that signal moisture problems.
Certified inspectors, thermal imaging, and lab-backed results for Gulf Coast homes
Mold Inspection and Testing Ocean Springs MS You Can Trust
Mold Inspection and Testing Ocean Springs MS is the fastest way to find out whether that musty smell, ceiling stain, or post-storm dampness is actually mold. We inspect crawl spaces, attics, and wall cavities across Jackson County, take air and surface samples, and give you lab results you can hand to your insurance adjuster. If you have had water damage, a roof leak, or storm surge flooding, call us before the problem spreads.
Careful work. Honest options.
About this service
What Mold Inspection and Testing Ocean Springs MS Really Involves
Mold Inspection and Testing Ocean Springs MS is a diagnostic service that locates hidden mold growth, measures spore counts in the air, and documents moisture problems before they rot your framing. We start with a full walk-through, then use a moisture meter, thermal imaging camera, and hygrometer to map wet zones inside walls, under hardwood flooring, and behind baseboards. We take air samples with a calibrated pump and surface swabs from suspect areas, then send them to an accredited lab. You get a written report with photos, spore counts, and a clear yes-or-no on whether remediation is needed.
Ocean Springs homes sit in one of the wettest, most humid pockets of Mississippi. Summer dew points hold above 70 degrees for months, winter storm fronts push rain through roof leaks, and crawl space moisture never really dries out on its own. That is why professional mold testing Ocean Springs MS homeowners call us for is usually triggered by a burst pipe, appliance overflow, or slab leak that went unnoticed for weeks. If you have smelled that damp, earthy odor in a closet or seen dark speckling along a baseboard, it is time to test, not guess.
- ✓ Lab-Backed Answers
- ✓ Hidden Mold Found Fast
- ✓ Insurance-Ready Documentation
- ✓ A Clear Next Step
What's included
What Is Included in Our Mold Inspection
Every mold inspection and testing Ocean Springs MS appointment includes the full diagnostic package. We do not charge extra for thermal imaging or crawl space access. Here is what you get.
Moisture and Thermal Readings
A moisture meter and FLIR thermal imaging camera check walls, ceilings, and floors for hidden wet spots. We log every reading with a photo so you can see exactly where the problem areas are.
Air Sampling
We set up calibrated air pumps to capture spores from the indoor air. At least one outdoor control sample is taken for comparison. This tells us whether indoor spore counts are elevated above normal background levels.
Surface Sampling
If we see visible growth, we take a swab or tape lift sample. The lab identifies the species, which matters because some molds are more hazardous than others. Stachybotrys and Aspergillus are treated differently than common Cladosporium.
Written Report with Lab Results
You get a full report with photos, moisture maps, lab data, and a plain-English summary. The report includes recommendations: no action needed, monitor, or remediation required. It is formatted for insurance and real estate use.
How it works
How Our Mold Inspection Process Works
We ask when the water event happened, what you have noticed, and whether anyone in the house has been getting sick. That call takes about 10 minutes and lets us bring the right equipment. If you need same-day mold inspection Ocean Springs MS, we will tell you on the call whether we can fit you in.
A certified mold inspector Ocean Springs walks the property with you, room by room. We check the attic decking, crawl space joists, under sinks, and around the water heater. We use a moisture meter and infrared thermometer to flag wet spots that look dry on the surface.
We set up air sampling pumps in at least two locations, one indoor and one outdoor control. Surface samples come from visible growth or suspect areas. Every reading gets photographed and logged. This step usually takes 45 to 60 minutes depending on square footage.
Samples ship to an accredited lab the same day. Standard turnaround is 24 to 48 hours. Rush analysis is available if you are under a real estate deadline or need to file an insurance claim quickly.
You get a written report with photos, moisture maps, spore counts, and a plain-English summary. If remediation is needed, we walk you through what it involves and what it costs. If it is not, we tell you that too.
STEP 01Phone Intake
We ask when the water event happened, what you have noticed, and whether anyone in the house has been getting sick. That call takes about 10 minutes and lets us bring the right equipment. If you need same-day mold inspection Ocean Springs MS, we will tell you on the call whether we can fit you in.
Tools & methods
Tools and Methods We Use
FLIR Thermal Imaging Camera
Detects temperature differences behind walls and under floors that indicate hidden moisture. Lets us find wet spots without cutting into finished surfaces.
Moisture Meter (DeWalt and RIDGID)
Pin-type and pinless meters measure moisture content in drywall, wood, and concrete. We log readings to track drying progress and confirm when materials are dry.
Bore Scope
A flexible camera that fits through small holes to inspect inside wall cavities and crawl spaces. We use it to confirm mold growth in areas we cannot see directly.
Air Sampling Pump
Draws a calibrated volume of air through a spore trap cassette. The cassette goes to the lab for analysis. This is the standard method for air quality mold testing.
Hygrometer
Measures relative humidity in each room and in the crawl space. High humidity readings tell us whether conditions are favorable for mold growth even without visible signs.
Dri-Eaz and Phoenix Dehumidifiers
When we find active moisture, we deploy commercial dehumidifiers to bring humidity down below 50 percent. That stops mold from spreading while we plan remediation.
Real results
Before and after.
Mold Inspection and Testing
Attic Mold After Roof Leak
A homeowner in St. Martin noticed dark staining on the attic decking after a spring storm. The roof had leaked slowly for weeks, and insulation was damp. Air samples showed elevated Aspergillus spores.
After: We documented the mold with photos and lab results, then removed affected insulation and treated the decking with antimicrobial spray. Post-remediation testing confirmed spore counts back to normal. The homeowner filed an insurance claim with our report.
Book this service →
Mold Inspection and Testing
Crawl Space Mold in Gulf Hills
A family in Gulf Hills had been dealing with musty odors for months. The crawl space had no vapor barrier, and joists were covered in white and black mold growth. Indoor air samples showed spore counts three times higher than outdoor.
After: We installed a vapor barrier, treated the joists, and ran dehumidifiers for three days. Clearance testing showed indoor spore counts matched outdoor levels. The musty smell was gone.
Book this service →
Mold Inspection and Testing
Mold Behind Drywall After Pipe Burst
A burst pipe in a Front Beach home soaked the wall behind the kitchen cabinets. The homeowner dried what they could see but did not realize moisture was trapped behind the drywall. Two weeks later, mold was visible along the baseboard.
After: We used thermal imaging to map the moisture, cut out affected drywall, and treated the framing. Air samples confirmed no elevated spores after remediation. The homeowner rebuilt with new drywall and trim.
Book this service → Problems we solve
Mold Problems We Solve in Ocean Springs
Most mold calls start with a smell, a stain, or a health symptom. Here are the most common problems we diagnose and fix for Ocean Springs homeowners.
Ask a pro →Musty odor with no visible mold
We use thermal imaging and a bore scope to find the source without tearing out walls. Air sampling confirms whether spores are elevated. Once we locate the moisture source, we fix it and treat the affected area.
Mold after a water heater leak
We inspect the area around the water heater with a moisture meter, check adjacent walls and flooring, and take samples. If mold is present, we remove affected materials, dry the framing, and verify with post-remediation testing.
Crawl space mold spreading into living space
We inspect the crawl space with a bore scope and moisture meter, test the air above, and recommend a vapor barrier plus ventilation improvements. If remediation is needed, we handle it and then retest to confirm clearance.
Mold discovered during a real estate transaction
We provide a full inspection report with lab results that satisfies lender and buyer requirements. If remediation is needed, we do it fast and provide a clearance report so the deal can close on schedule.
Transparent pricing
Mold Inspection and Testing Pricing
$300 - $650 depending on scope
Typical 2026 pricing for mold inspection and testing Ocean Springs MS ranges from $300 to $650 for most homes. That covers the on-site inspection, thermal imaging, air sampling, and lab analysis. Larger homes, crawl space inspections, and rush lab turnaround cost more. We give you a flat quote before we start, so you know exactly what you are paying. If you are comparing mold testing services Ocean Springs providers, ask whether their price includes lab fees and a written report. Ours does.
A mold inspection costs a fraction of remediation. Finding mold early, or confirming it is not there, saves you thousands. Our reports are insurance-ready and include lab data you can act on immediately.
•affects cost
Larger homes take longer to inspect and require more sampling points. A 1,200-square-foot home might need two air samples, while a 3,500-square-foot home could need four or five.
Get a quote ↗•affects cost
Each air sample and surface swab has a lab fee. More samples give you a more complete picture but increase the total cost. We recommend the minimum needed for accurate results.
Get a quote ↗•affects cost
Crawl space inspections take extra time and require protective equipment. If your crawl space has limited access or standing water, that adds to the labor.
Get a quote ↗•affects cost
Standard lab results come back in 24 to 48 hours. If you need results faster for a real estate closing or insurance deadline, rush analysis is available for an additional fee.
Get a quote ↗ Proof you can check
Licensed, Certified, and Reviewed
- IICRC WRT (Water Restoration Technician) · Institute of Inspection, Cleaning and Restoration Certification
- IICRC AMRT (Applied Microbial Remediation Technician) · Institute of Inspection, Cleaning and Restoration Certification
- IICRC ASD (Applied Structural Drying) · Institute of Inspection, Cleaning and Restoration Certification
- EPA Lead-Safe Certification · U.S. Environmental Protection Agency
- Mississippi State Board of Contractors License · Mississippi State Board of Contractors
Customer reviews
What Our Customers Say
★★★★★
“We had a roof leak last spring and thought it dried out fine. Six months later I noticed a musty smell in the hallway. Water Damage Restoration Ocean Springs came out, found moisture behind the drywall with their thermal camera, and took air samples. Lab confirmed mold. They handled the remediation too. Whole thing took about a week.”
KM
Karen M.Homeowner, Gulf Hills
✓ Verified“
★★★★★
“I manage several rental properties and needed fast mold testing services in Ocean Springs for a tenant complaint. They got someone out the next morning, took samples, and had results back in two days. The report was clean and professional, which made it easy to show the tenant there was no issue. I use them for all my properties now.”
DR
David R.Property Manager, St. Martin
✓ Verified★★★★★
“After storm surge flooding, we were worried about mold in the crawl space. The inspector spent almost three hours under the house with a moisture meter and bore scope. He showed me photos of everything. Turned out we needed a vapor barrier and some joist treatment. No mold remediation needed. I appreciated that they did not try to upsell me.”
LT
Lisa T.Homeowner, East Beach
✓ VerifiedMost residential mold inspections in Ocean Springs run $300 to $650 depending on square footage and how many samples we take. A basic inspection with two air samples and one surface swab typically lands around $350 to $400. Crawl space inspections or homes over 3,000 square feet cost more because they take longer and require more sampling points. We quote flat rates before we start.
The on-site inspection takes two to three hours for an average home. Lab results come back in 24 to 48 hours. If you need results faster, we can request rush analysis for an additional fee, which usually gets you a report within 24 hours. Total turnaround from call to written report is typically three days.
Every inspection includes a full visual walk-through, moisture meter readings, thermal imaging of suspect walls and ceilings, air sampling with an outdoor control, surface sampling of visible growth, and a written report with photos and lab results. We also check the attic, crawl space, and HVAC closet because those are the three places mold hides most often in Gulf Coast homes.
Yes, if the water sat for more than 48 hours or if you smell a musty odor weeks later. Mold can start growing within 24 to 48 hours of a water event. Even if you dried everything yourself, hidden moisture behind baseboards or under hardwood flooring can feed mold for months. Testing confirms whether the space is actually clean or just looks clean.
Ready when you are
Schedule Your Mold Inspection and Testing Ocean Springs MS Today
If you smell something musty or see dark spots on your walls, do not wait. Mold spreads fast in Gulf Coast humidity. Call us now and we will schedule a certified inspector, take samples, and get you lab results within 48 hours. Flat pricing, no surprises.
Book Inspection Now (228) 279-0515 →
Request an appointment
Contact Our Ocean Springs Team
Call us at (228) 279-0515 any time, day or night. We answer live and dispatch immediately for emergency water damage. For non-emergency questions or to schedule an inspection, email us or stop by our office in Ocean Springs. We serve all of Jackson County.
Call anytime(228) 279-0515Email the office[email protected]
Office hoursOpen 24 hours · 7 days a week